5b2ded89-1274-4242-bf0c-e425a2ec9b0520250114043404436wseas:wseasmdt@crossref.orgMDT DepositWSEAS TRANSACTIONS ON CIRCUITS AND SYSTEMS2224-266X1109-273410.37394/23201http://wseas.org/wseas/cms.action?id=28612920242920242310.37394/23201.2024.23https://wseas.com/journals/cas/2024.phpAbdelkaderGourbiInstitute of Science and Applied Techniques, Ahmed Ben Bella Oran 1 University, Oran, ALGERIAMohamedMiloudiAPELEC Laboratory, Electrical Engineering Department, Djillali Liabes University, Sidi Bel Abbes , ALGERIAHoucineMiloudiAPELEC Laboratory, Electrical Engineering Department, Djillali Liabes University, Sidi Bel Abbes , ALGERIAMohammed HamzaBermakiAPELEC Laboratory, Electrical Engineering Department, Djillali Liabes University, Sidi Bel Abbes , ALGERIAThis paper presents an experimental study of the high-frequency impedance behavior of four types of single-phase induction motors: Split-Phase Induction Motor (SPIM), Permanent Split Capacitor Induction Motor (PCIM), Capacitor Start Induction Motor (CSIM) and Single Phase Repulsion Motor (RIM). A differential-mode impedance and phase angle over a range of frequencies, including resonance and anti-resonance points, are the focus of the present study. The obtained results show that every type of motor has distinctive impedance characteristics; the RIM always shows higher impedance than other motors, whereas the CSIM exhibits lower impedance in low frequencies. Those differences unveil the influence of the motor design on Electromagnetic Compatibility (EMC) performance, since high-impedance motors, such as the RIM, present lower Electromagnetic Interference (EMI) emissions and lower susceptibility to external electromagnetic interference, therefore better general EMC performance. Also, the frequencies of resonance and anti-resonance vary between the motors, which is also reflected in their different electrical and structural designs. The study provides helpful insights into the optimization of motor designs to achieve better EMC compliance and operational stability in various applications.123020241230202426127326https://wseas.com/journals/cas/2024/a505101-020(2024).pdf10.37394/23201.2024.23.26https://wseas.com/journals/cas/2024/a505101-020(2024).pdf10.1007/978-981-99-9295-9_1X. Ruan, L. Xie, Q. Ji, and X. Yuan,“ in Conducted Electromagnetic Interference in Power Converters: Modeling, Prediction and Reduction”, Singapore: Springer Nature Singapore, 2024, pp. 1–24. https://doi.org/10.1007/978-981-99-9295-9_1. 10.1109/telfor.2012.6419398M. Miloudi, A. Bendaoud, H. Miloudi, S. Nemmich and H. Slimani, “Analysis and reduction of common-mode and differentialmode EMI noise in a Flyback switch-mode power supply (SMPS)”, 2012 20th Telecommunications Forum (TELFOR), Belgrade, Serbia, 20-22 November 2012, pp. 1080-1083. https://doi.org/10.1109/TELFOR.2012.64193 98. 10.20998/2074-272x.2024.3.05M. E. Lahlaci, M. Miloudi and H. Miloudi, “Experimental electromagnetic compatibility of conducted electromagnetic interferences from an IGBT and a MOSFET in the power supply”, Electrical Engineering & Electromechanics Journal, Vol. 3, pp. 38-43, 2024. https://doi.org/10.20998/2074- 272X.2024.3.05. M. Miloudi, H. Miloudi, A. Bendaoud, M. A. Salhi and A. N. Al-Omari, “Experimental Characterization of the High-Frequency Isolating Power Transformer”, Journal of Electrical Engineering and Computer Science (JEECS), Vol.86, No.4, 2019, pp. 211-218. 10.55549/epstem.1409311H. Miloudi; M. Miloudi, M. H. Bermaki, A. Gourbi and A. Bendaoud, “Optimization of EMC Filter for a Variable Speed Drive System in Electric Aircraft”, The Eurasia Proceedings of Science Technology Engineering and Mathematics, Vol. 26, 2023, pp. 60-60. https://doi.org/10.55549/epstem.1409311. 10.23919/emcjapan/apemcokinaw58965.2024.10584956S. Kim, K. Yang, Y. Yu, J. Park, C. Jo, and S. Jung, “Optimal Common Mode Target Impedance for Conducted Emission Noise Suppression in Motor Driver Circuits”, 2024 IEEE Joint International Symposium on Electromagnetic Compatibility, Signal & Power Integrity: EMC Japan / Asia-Pacific International Symposium on Electromagnetic Compatibility (EMC Japan/APEMC Okinawa), Ginowan, Okinawa, Japan, 20-24 May 2024, pp. 669-672. https://doi.org/10.34385/proc.82.FriAM1C.4. 10.23919/emcjapan/apemcokinaw58965.2024.10584978T. Hoshino, M. Sao, and T. Tominaga, “Immunity test result and consideration of open-source flight-controller mounting UAV for applying IEMI protection device”, 2024 IEEE Joint International Symposium on Electromagnetic Compatibility, Signal & Power Integrity: EMC Japan / Asia-Pacific International Symposium on Electromagnetic Compatibility (EMC Japan/APEMC Okinawa), Ginowan, Okinawa, Japan, 20-24 May 2024, pp. 681-684. https://doi.org/10.23919/EMCJapan/APEMC Okinaw58965.2024.10584978. 10.1109/access.2024.3459641Y. Moreno, G. Almandoz, A. Egea, I. Eguren, and A. Urdangarin, “EMI Simulation of Permanent Magnet Motor Drive Systems”, IEEE Access, Vol. 12, 2024, pp. 133153- 133164. https://doi.org/10.1109/ACCESS.2024.34596 41. 10.1109/access.2021.3054514Z. Zhang, Y. Hu, X. Chen, G. W. Jewell and H. Li, “A Review on Conductive CommonMode EMI Suppression Methods in Inverter Fed Motor Drives”, IEEE Access, Vol. 9, 2021, pp. 18345-18360. https://doi.org/10.1109/ACCESS.2021.30545 14. 10.23919/emcjapan/apemcokinaw58965.2024.10585229D. Kircher, B. Deutschmann and H. Helldorff, “A Novel Method for Testing the Electromagnetic Immunity of the Short Circuit Protection Function of Smart Power Switches”, 2024 IEEE Joint International Symposium on Electromagnetic Compatibility, Signal & Power Integrity: EMC Japan / AsiaPacific International Symposium on Electromagnetic Compatibility (EMC Japan/APEMC Okinawa), Ginowan, Okinawa, Japan, 20-24 May 2024, pp. 661- 664. https://doi.org/10.23919/EMCJapan/APEMC Okinaw58965.2024.10585229. 10.23919/emcjapan/apemcokinaw58965.2024.10585185T. Ishida and O. Fujiwara, “Revision Status and Further Study Issue of International Standard on System Level ESD Immunity Testing”, 2024 IEEE Joint International Symposium on Electromagnetic Compatibility, Signal & Power Integrity: EMC Japan / AsiaPacific International Symposium on Electromagnetic Compatibility (EMC Japan/APEMC Okinawa), Ginowan, Okinawa, Japan, 20-24 May 2024, pp. 126- 129. https://doi.org/10.23919/EMCJapan/APEMC Okinaw58965.2024.10585185. 10.1109/sefet55524.2022.9909277A. Bhakthavachala, K. Anuradha, and S. Tarakalyani, “Design and Product Development of a Dual Channel Line Impedance Stabilization Network for Electromagnetic Interference Compatibility. 2022 IEEE 2nd International Conference on Sustainable Energy and Future Electric Transportation (SeFeT), Hyderabad, India, 04-06 August 2022, pp. 1-6. https://doi.org/10.1109/SeFeT55524.2022.990 9277. 10.1109/emceurope51680.2022.9900988A. D. Khilnani, A. E. Pena-Quintal, E. Ballukja, M. Sumner, D. W. P. Thomas, and L. Sandrolini, “Influence of Impedance Interaction & Comparability on Spectral Aggregation (2–150 kHz) in DC Grids”, 2022 International Symposium on Electromagnetic Compatibility – EMC Europe, Gothenburg, Sweden, 05-08 September 2022, pp. 788-792. https://doi.org/10.1109/EMCEurope51680.20 22.9900988. 10.1109/emceurope51680.2022.9901300E. Tas and F. Pythoud. “An Interlaboratory Comparison on Radiated Immunity IEC 61000-4-3”, 2022 International Symposium on Electromagnetic Compatibility – EMC Europe, Gothenburg, Sweden, 05-08 September 2022, pp. 126-130. https://doi.org/10.1109/EMCEurope51680.20 22.9901300. 10.1109/emceurope51680.2022.9901009T. Kasai and T. Onigata, “A Study on EMC Test Methods for ESD-Induced Conducted Noise through Space Structures”, 2022 International Symposium on Electromagnetic Compatibility – EMC Europe, Gothenburg, Sweden, 05-08 September 2022, pp. 479-483. https://doi.org/10.1109/EMCEurope51680.20 22.9901009. 10.1109/tpel.2023.3327258S. Nayak, V. Pandey and K. Hatua, “A Dithering Technique for Mitigation of Conducted Emission Noise of SiC MOSFET Based VSI Driving an Induction Motor”, in IEEE Transactions on Power Electronics, vol. 39, no. 2, Feb. 2024, pp. 2281-2293. https://doi.org/10.1109/TPEL.2023.3327258. 10.1109/npec57805.2023.10385027R. Kichouliya, S. Sundar and B. P. Reddy, “Power Line EMI Filter Design of Power Converters to Meet the Conducted Emission Specifications of MIL-STD-461G”, National Power Electronics Conference (NPEC). 2023 11th National Power Electronics Conference (NPEC), Guwahati, India, 14-16 December 2023, pp. 1-6. https://doi.org/10.1109/NPEC57805.2023.103 85027. 10.1109/sefet57834.2023.10245535A. Ganjavi, D. Kumar, F. Zare and P. Davari, “Analyzing the Effect of Choke Placement on Differential-Mode Supra-Harmonics in Variable Frequency Drives: New Standardization”, IEEE 3rd International Conference on Sustainable Energy and Future Electric Transportation (SEFET). 2023 IEEE 3rd International Conference on Sustainable Energy and Future Electric Transportation (SEFET), Bhubaneswar, India, 09-12 August 2023, pp. 1-6. https://doi.org/10.1109/SeFeT57834.2023.102 45535. 10.1109/pqemc-lf58184.2023.10212014I. Nuca, L. Wan, P. . -. M. Nicolae, I. . -. D. Nicolae, F. Grassi and X. Wu, “Analysis of Common Mode Currents and Harmonic Pollution at Supplying Induction Motors from Static Converters with Variable Modulation Frequency”, 2023 Power Quality and Electromagnetic Compatibility at Low Frequency (PQEMC-LF), Craiova, Romania, 28-30 June 2023, pp. 57-60. https://doi.org/10.1109/PQEMCLF58184.2023.10212014. 10.1109/ecce53617.2023.10362219T. Li, R. Olson, H. Abdallah, N. Sivadanam and R. M. Cuzner, “Modeling and Validation of Common-mode Emissions of Silicon Carbide Enabled Motor Drive in Extended EMC Frequency Range Between 2 kHz and 30 MHz”, 2023 IEEE Energy Conversion Congress and Exposition (ECCE), Nashville, TN, USA, 29 October 2023, pp. 2904-2911. https://doi.org/10.1109/ECCE53617.2023.103 62219. 10.1109/lemcpa.2023.3284229V. Ghatge, L. Buysse, D. Vanoost, J. Catrysse and D. Pissoort, “Applying the Goal Structuring Notation (GSN) to Argue Compliance of Equipment With the European EMC Directive”, in IEEE Letters on Electromagnetic Compatibility Practice and Applications, Vol. 5, No. 4, Dec. 2023, pp. 113-121. https://doi.org/10.1109/LEMCPA.2023.32842 29. 10.1109/lemcpa.2023.3248641A. J. Otto, A. R. Botha, P. S. V. d. Merwe and T. Nkawu, “Characterizing Transient RadioFrequency Interference From Motors for the Square Kilometer Array Radio Telescopes”, in IEEE Letters on Electromagnetic Compatibility Practice and Applications, Vol. 5, No. 2, June 2023, pp. 53-56. https://doi.org/10.1109/LEMCPA.2023.32486 41. 10.37394/232017.2023.14.8Y. Swami, “Design Guidelines for Low Power Embedded Systems using Low Power Electronics”, WSEAS Transactions on Electronics, Vol. 14, 2023, pp. 65-70, http://dx.doi.org/10.37394/232017.2023.14.8. 10.37394/232017.2023.14.7A. Alahmad, F. Kaçar, C. P. Uzunoğlu, “Medium-Voltage Drives (MVD) - Performance Analysis of Seven-Level Cascaded H-Bridge Multilevel Driver”, WSEAS Transactions on Electronics, Vol. 14, 2023, pp. 57-64. http://dx.doi.org/10.37394/232017.2023.14.7. 10.37394/232017.2023.14.1O. Kim, Y. Han, J. Jeong, “Design and Implementation of Painting and Replacement Automation Robot System in Spindle Line for Smart Manufacturing”, WSEAS Transactions on Electronics, Vol. 14, 2023, pp. 1-6. http://dx.doi.org/ 10.37394/232017.2023.14.1. 10.37394/232017.2024.15.3RajathIthal H. L., Shylashree N., Mamatha A. S., Nikhil B. G., “Design and Comparison of Constant Transconductance Architectures”, WSEAS Transactions on Electronics, Vol. 15, 2024, pp. 17-26, https://doi.org/10.37394/232017.2024.15.3. 10.37394/232017.2024.15.1J. Ravindrababu, D. Swathi, J. V. Ravi Teja, J. V. Ravi Chandra, N. Pranavi Sri, Shaik Arshiya, “Analysis of Multiuser Detectors and Performance improvement in DS-CDMA system using Multistage Multiuser Detection Techniques”, WSEAS Transactions on Electronics, Vol. 15, 2024, pp. 1-10. https://doi.org/10.37394/232017.2024.15.1. 10.37394/232017.2022.13.16Jayadeva G. S., Nikhil Murali, Meghana S., Raksha K. Kumar, Nithin Anil Nair, “Design and Implementation of a High-Speed D Flip Flop using CMOS Inverter Logic”, WSEAS Transactions on Electronics, vol. 13, , 2022, pp. 125-129. https://doi.org/10.37394/232017.2022.13.16. 10.37394/232017.2022.13.15Jinliang Wu, Xiaoyang Zheng, Xinglong Pei, “An Anti-Noise Gearbox Fault Diagnosis Method based on Multi-Scale Transformer Convolution and Transfer Learning”, WSEAS Transactions on Electronics, vol. 13, 2022, pp. 115-124. https://doi.org/10.37394/232017.2022.13.15. 10.1109/speedam48782.2020.9161915A. Hoffmann and B. Ponick, “Statistical Deviation of High-Frequency Lumped Model Parameters for Stator Windings in ThreePhase Electrical Machines”, 2020 International Symposium on Power Electronics, Electrical Drives, Automation and Motion (SPEEDAM), Sorrento, Italy, 24- 26 June 2020, pp. 85-90. https://doi.org/10.1109/SPEEDAM48782.202 0.9161915. 10.1016/j.apacoust.2016.10.012A. Glowacz, Z. Glowacz, “Diagnosis of stator faults of the single-phase induction motor using acoustic signals”, Appl. Acoust., Vol. 117, 2017, pp. 20–27. https://doi.org/10.1016/j.apacoust.2016.10.01 2. 10.1109/iecon.2002.1185403N. Abdel-Rahim and A. Shaltout, “A. Operation of single-phase induction motor as two-phase motor”, In Proceedings of the IEEE 2002 28th Annual Conference of the Industrial Electronics Society (IECON 02), Seville, Spain, 05-08 November 2002; pp. 967–972. https://doi.org/10.1109/IECON.2002.1185403 10.1109/iceeict53905.2021.9667888M. R. Rahman, M. A. Taleb, M. S. Shadi and M. M. Islam, “Design of Rotor for SinglePhase Induction Motor to Improve Startability in Refrigerator Application”, In Proceedings of the 2021 5th International Conference on Electrical Engineering and Information Communication Technology (ICEEICT), Dhaka, Bangladesh, 18-20 November 2021; pp. 1–5. https://doi.org/10.1109/ICEEICT53905.2021. 9667888. 10.1109/access.2023.3349018H. Miloudi, M. Miloudi, S. Ardjoun, M. Metwally, A. Telba, M. Denai, U. Khaled, A. Ewais, “Electromagnetic Compatibility Characterization of Start-Capacitor SinglePhase Induction Motor”, IEEE Access, Vol. 12, 2024, pp. 2313–2326. https://doi.org/10.1109/ACCESS.2023.33490 18. 10.1109/tpel.2010.2047734K. Mainali and R. Oruganti, “Conducted EMI Mitigation Techniques for Switch-Mode Power Converters: A Survey”, IEEE Trans. Power Electron., Vol. 25, No. 9, 2010, pp. 2344–2356. https://doi.org/10.1109/TPEL.2010.2047734. 10.24084/reepqj23.205M. Buzdugan, “A Brief Introduction in the Mitigation of Conducted-Electromagnetic Interference Issues”, In Proceedings of the 19th International Conference on Renewable Energies and Power Quality (ICREPQ’21), Almeria, Spain, 28-30 July 2021; Renewable Energy and Power Quality Journal, Vol. 19, 2021, pp. 373–378. https://doi.org/10.24084/repqj19.297. 10.1007/s40998-016-0007-zM. Mohammadi-Rostam, M. Shahabi, “Modeling Induction Motor for Prediction of High Frequency Problems”, Iran. J. Sci. Technol. Trans. Electr. Eng., Vol. 40, 2016, pp. 13–22. https://doi.org/10.1007/s40998- 016-0007-z. V. Särkimäki, “Radio Frequency Measurement Method for Detecting Bearing Currents in Induction Motors”, Ph.D. Thesis, Lappeenranta University of Technology, Acta Universitatis Lappeenrantaensis, Finland, 2009, [Online]. https://urn.fi/URN:ISBN:978- 952-214-747-9 (Accessed Date: November 4, 2024). 10.1201/9781420027730J. F. Gieras, C. Wang,; J. C. Lai, ”Noise of Polyphase Electric Motors”, 1st ed.; CRC Press: Boca Raton, FL, USA, 2006. https://doi.org/10.1201/9781420027730. 10.1109/access.2024.3406490M. Yang, B. T. Phung, “Motor Winding Insulation Degradation Under Repetitive Voltage Pulses”, IEEE Access, Vol. 12, 2024, pp. 77658–77674. https://doi.org/10.1109/ACCESS.2024.34064 90. 10.1016/j.ymssp.2014.08.022V. Ghorbanian, J. A. Faiz, “Survey on Time and Frequency Characteristics of Induction Motors with Broken Rotor Bars in Line-Start and Inverter-Fed Modes”, Mech. Syst. Signal Process., Vol. 54–55, 2015, pp. 427–456. https://doi.org/10.1016/j.ymssp.2014.08.022. H. Jaakkola, “Electromagnetic Compatibility of Frequency Converter Controlled Air Conditioning Fans in a Cruise Vessel Environment”, Master’s Thesis, LUT University, School of Energy Systems, Lappeenranta, Finland, 2020, [Online]. https://urn.fi/URN:NBN:fi-fe2020101383959. (Accessed Date: December 1, 2024). 10.1049/iet-epa.2019.0773A. Rahimi, K. Kanzi, “High-Frequency Modelling of Permanent Magnet Synchronous Motor for Conducted EMI Studies”, IET Electr. Power Appl., Vol. 14, No. 11, 2020, pp. 2027–2036. https://doi.org/10.1049/ietepa.2019.0773. 10.23919/cjee.2022.000022F. Fan, Z. Zhao, H. Jie, Q. Sun, P. Tu, Z. Shu, W. Wang, K. Y. See, “Impact of Motor Stator Winding Faults on Motor Differential-Mode Impedance and Mode Transformation”, Chinese J. Electr. Eng., Vol. 8, No. 3, 2022, pp. 12–21. https://doi.org/10.23919/CJEE.2022.000022. 10.1109/tmag.2019.2949031D. Y. Um,; G. S. Park, “Determination Scheme of Stator Parameters for Making Rotating Fields Circular in a Single-Phase Induction Motor”, IEEE Trans. Magn., Vol. 56, No. 1, 2019, pp. 1–5. https://doi.org/10.1109/TMAG.2019.2949031. 10.1109/paep49887.2020.9240878O. Iegorov, O. Iegorova, M. Kundenko, A. Milenin, “Single-Phase Induction Motors Winding Parameters Optimization with Maximum Efficiency”, In Proceedings of the 2020 IEEE Problems of Automated Electrodrive. Theory and Practice (PAEP), IEEE, Kremenchuk, Ukraine, 21-25 September 2020; pp. 1–4. https://doi.org/10.1109/PAEP49887.2020.924 0878. 10.1007/s11668-022-01445-2M. A. Sheikh, S. T. Bakhsh, M. Irfan, N. M Nor, G. Nowakowski, “A Review to Diagnose Faults Related to Three-Phase Industrial Induction Motors”, J. Fail. Anal. Prev., Vol. 22, No. 4, 2022, pp. 1546–1557, [Online]. https://khub.utp.edu.my/scholars/id/eprint/165 31 (Accessed Date: December 1, 2024). 10.11591/ijece.v13i4.pp3829-3837M. Salama, W. M. Abdelkarim, “Improving the starting torque and overall efficiency of split single phase induction motor”. International Journal of Electrical and Computer Engineering (IJECE), Vol. 13, No 4, 2023, pp. 3829-3837. http://doi.org/10.11591/ijece.v13i4.pp3829- 3837. 10.1109/emes.2017.7980388A. Michaelides, T. Nicolaou, “Starting and Running the Induction Motor with a Variable Capacitor”, In Proceedings of the 2017 14th International Conference on Engineering of Modern Electric Systems (EMES), IEEE, Oradea, Romania, 01-02 June 2017; pp. 87– 90. https://doi.org/10.1109/EMES.2017.7980388. V. Sarac, “FEM Aided Design of Permanently Split Capacitor Motor Under Different Operating Regimes”, Electr. Eng., Electron., Autom., Vol. 64, No. 2, 2016, pp. 63–71, [Online]. https://eprints.ugd.edu.mk/id/eprint/15926. (Accessed Date: December 1, 2024). 10.1109/iemdc.2019.8785265A. Crăciunescu, “The Development of a New Type of Repulsion-Induction Motor”, In Proceedings of the 2019 IEEE International Electric Machines & Drives Conference (IEMDC), IEEE, San Diego, CA, USA, 12-15 May 2019; pp. 1447–1451. https://doi.org/10.1109/IEMDC.2019.8785265